Complying with Australian Standards when it comes to providing a bayonet fitting to your customers home.
I quite often receive phone calls from customers either looking to convert an existing gas point in there living room that feeds a room heater to a bayonet fitting or customers who wish to extend there existing gas main into there living room for the installation of a bayonet fitting. Ok so far so good right? Yes not a problem at all I agree, BUT as a licensed gas fitter in Adelaide I know the intention of what this bayonet fitting is being supplied for and its not to hang coats on or rest a book up against, its for the future installation of a portable gas room heater and is therefore my duty as a gas fitter to ensure that when I leave the property a few things have been performed.
Adequate room ventilation from the outside of the house (atmosphere) both at low level and high level has been provided (extremely crucial). It is very important to note such information about all of this is written clearly on the Certificate of Compliance, things such as the position of the air vents, the current size of the room and the exact location of the bayonet fitting, by doing this you are completely covering yourself from future liabilities after you have left the property.
In most installations that I have been to the appliance that is going to be used is not on site at this stage but is being collected shortly, so it is vital to write all the information about your installation down on a COC.
As you may or may not be aware of portable gas appliances burn off the air from the room and also emit back into the room so it Crucial that free air from outside is readily available other wise carbon monoxide poisoning can occur and lead to the loss of life. It is amazing though on this note how many people will still try and coach me into just providing a bayonet fitting and they promise to put the vents in later themselves or something similar, wow really would you seriously risk your life or that of some one elses? I certainly will never and that is why I have taken the time this week to post about the serious nature of having a bayonet fitting installed which complies with Australian Standards by a licensed gas fitter.
I can remember when I started my apprenticeship as a plumber every toilet pan was secured to the floor with a sand and cement mix (mortar). We would place the toilet pan on the floor and mark out the foot print with a pencil and the remove it again, the next step would be to cut a hole in the floor under the pan for a key (this would create a lock between the pan and the floor). The final step would be to mix up a stiff mix of mortar and place a large amount of this inside the under neath of the toilet pan and also a mound on the floor. Then the challenge would be to carefully turn the pan over and land it on top of the mortar bed without loosing the mortar inside the pan, once this was achieved you would then level the pan off and just carefully dress the excess mortar away and clean the floor etc with a damp sponge.
Over the years securing a toilet pan to the floor has changed in a good way. Today the method most commonly used by plumbers to fix a toilet pan to the floor is with clear sanitary grade silicone. How I perform this is to put the toilet onto the floor in its desired location, place some small packers or wedges under the toilet to raise it by approx 2 to 3 millimeters and until a level toilet pan is achieved (this providing the floor slope is not to drastic, I don't like to have a larger gap than 5 or 6 millimeters at the front of the pan when using silicone), then go around the whole base of the toilet pan with the silicone applying it to the gap between the floor and the toilet pan, once this has been performed I then spray a solution of soap and water over the silicone and wipe the excess off. The purpose of the soap and water solution is to avoid the excess silicone sticking to the floor and also your fingers as you carefully remove the excess silicone.
Like the method of using mortar mix it is advisable to always leave the toilet pan as long as possible before its initial use, but as a minimum I always suggest 24 hours before any sort of weight is applied to the pan, your plumber will always be the best person to advise this of course.
Please leave any comments about any of your experiences with setting a toilet pan to floor or visit us at:
Winter 2015 has been busy again for us at Mayfair Plumbing with the Hydro Jet crew clearing year's worth of silt and sediment build up from our customer's storm water drain lines. Not only have we been busy jetting storm water systems but also blasting our regular customers sewer and trade waste drainage systems.
Successfully taming the hydro jetter is not a 5 minute lesson it takes year's worth of experience in getting to know the mannerism of the high pressure jetter in all the many different situations it can get into. You're talking about a hose that has over 4000 psi of pressure going through it with a variety of different nozzles attached if this was to accidentally come out of the drain or perhaps go into the wrong drain line it spells BIG TROUBLE BIG TIME, that's why you need to know how to tame the jet.
At Mayfair Plumbing we use the Honda V Twin engine to power our hydro jetting drain cleaning machine. Strapped to the back of this piece of muscle is an Italian made water pump which pushes up to 26 liters per minute through the various nozzles connected to the remote mini reel. If you think about a garden hose turned on full with a watering nozzle connected to it you will notice it goes off like an out of control snake, but then take this mean piece of kit which operates at over 100 times the pressure you can get a picture of just how dangerous this machine can be in the wrong hands.
There are various nozzles on the market which you can use with the hydro jet drain cleaner, take for example the screw driver nozzle it relies on a huge amount of reverse thrust so it wants to really race down the drain and hit the blockage fast, you want to be on your A game when this bad boy gets full throttle introduced to it otherwise it will take off out of your hands. Then take the wart hog nozzle, this is a self-propelling nozzle which relies more upon huge volumes of water being dis-burst into the drain but also operates at a large amount of pressure which is not to be sneezed at.
How the jetter performs in smaller tight drains such as 90 mm storm water lines and 50 mm waste lines is really where the inexperienced jetting operator can be caught off guard. Entering these very tight throats of an elbow in these drains needs to be done with due caution as the jetter can get stuck and this can happen at the blink of an eye. When the jet is in full throttle mode the hose will become stiff and drive through these bends with a bit of manoeuvering, but when the throttle is turned down the hose becomes very limp and can drop into places you really don't want the jetter to be and bang you've got it stuck.
It is due to all of the above points I have mentioned that a lot of plumbers simply will not get involved hydro jet drain cleaning, its serious business and needs to be treated with great respect otherwise the consequences can be catastrophic. Jet blasting of drain lines is the best method of cleaning drains and any licensed plumber would vouch for that but it must only be performed be a trained technician. If you have a hydro jetting story we would love to hear from you at, ATT: Aaron and email address: email@example.com
In South Australia we have a government organisation which looks after the maintenance of the sewer infrastructure and there name is SA WATER. When a plumber Adelaide is contacted by a customer to attend a blocked drain the best practice by an ethical plumbing company is to arrive on site and identify where the government inspection point is, also known as the government IO or the Government or the Gov IO depending on which plumber you speak with. The purpose of identifying the government IP is to establish where in the drain line the blockage actually lies. The government IP is the point where the customers internal sewer drain line joins into the main infrastructure of the street or easement which ever the case. If the customer does not have an easement then they will have a government IP located somewhere out the front of there property connecting them to the street sewer mains or in the case of a sewer easement then there will be a government inspection point located close to a boundary (usually at the rear of the property but not always, it can be on a side boundary sometimes).
If for some reason the plumber Adelaide cannot locate the government IP there are a few options, one is to contact SA WATER and ask for directions over the phone and if there is still no success with this then the licensed plumber can request that an SA WATER employee come out and locate it with there metal detectors etc (it is important to note that SA water do not always come out straight away, usually in a 5 hour window for metro Adelaide).
Once a government inspection point is located it can be opened and inspected to asses where the blockage lies. If the inspection chamber is full of sewerage this indicates that there is a blockage on the SA WATER side of the drainage line and if the inspection chamber is empty this indicates there is a blockage inside the customers internal sewer drainage systems.
So if it does happen that the Adelaide Plumber finds the government IO to be full you get a "FREE DRAIN UN BLOCKED", that's right, your plumber from Mayfair Plumbing and Gasfitting will fill in a plumbers claim form get you to sign it and SA WATER will attend the site and have your drain from the connection point to the street cleaned. In most cases this is the only cause of the customers blocked drain Adelaide, but in some circumstances the plumber may also need to return with the HYDRO JET DRAIN CLEANER and also have the internal drain pipes cleared.
Of course if the government inspection point was found not to be blocked then the plumber will need to hydro jet your drain lines at your cost to un block your sewer drain in Adelaide, South Australia, but this is determined only after the government inspection point has been opened. If you have engaged an ethical plumber this is how he or she will go about helping you with your blocked drain.
Changes to free standing natural gas meter outlet connections in Adelaide, with the recent introduction of the "10 Light Fitting" for all new gas meter installations.
There still seems to be a lot of Gasfitters in Adelaide and across South Australia that are not across the changes which came into place in February 2015 for the installation of all new domestic free standing natural gas meters (i.e. not fixed enclosures or wall boxes).
The current free standing meter outlet connection with the rubber olive, plastic 1" nut and aluminium hoop is being phased out and the meter is now being supplied with a new fitting known as a "10 light fitting" (in picture below). The 10 light fitting is a 3/4" threaded liner BSP, a cap nut and a flat washer when supplied from new.
When installing the new consumer gas pipe work to the new free standing meter the gas fitter must now construct the old style of hoop connection to the gas meter from the consumers new pipe out of either copper or galv (in picture below). When constructing this connector piece it must replicate the old aluminium hoop the best as possible, so it is requested that the plumber get the new hoop connection in a tight radius, similar to that of the old hoop connection and as tight as physically possible (90mm from center to center maximum) (in picture below).
The new 10 Light Fitting is 3/4" MI in size at the point where the gas plumber will connect onto it, a reducing bush is required for the gas fitter to then get back to the size of the first leg of the consumer mains, unless of course the consumer mains is only 3/4" in size which is pretty rare in Adelaide as majority of natural gas lines are either 1", 1 and 1/4" or perhaps 1 and 1/2" so a reducing bush is most definitely needed.
If you are a plumber in Adelaide who is licensed to work with natural gas this is an important piece of information to have stored away in your head as there are still huge rebates on offer to the public to have natural gas installed to there property so you are sure to come across a free standing meter in the very near future. For further information visit Australian Gas Networks or APA.
At MAYFAIR Plumbing and Gasfitting my passion has always been to help the residents of Adelaide with there Emergency Plumbing situations. Over the last 12 months I have been working very hard to get my presence on the internet for Emergency Plumbing to position number 1 on google so that we can be the NUMBER 1 plumber for emergencies in Adelaide, well finally it has started to happen. YES We are number 1 on google for emergency plumbers adelaide and the phone has been ringing hot.
A few of the jobs which I have been asked to help various customers of myn with this week in particular were taps that would not shut off at all which meant that water was continually running down the kitchen sink. Another emergency call was also for a burst water pipe under the kitchen sink, the kitchen sink mixer tap had come loose over time and every time that my customer moved the tap the stainless steel braided water hoses would move and over time they started to perish the internal rubber hose which in turn had led to a an emergency plumber call out.
There has also been a few Hot Water Repairs I have been asked to attend to, one was a Bosch 21e which was showing an error code II, in most cases this indicates some kind of ignition failure, but when I arrived at the job and opened the casing of the of the Hot Water unit I noticed there was water discharging out of the copper heat ex changer, I called Bosch Hot Water while I was on the job and clarified that the heat ex changer was still under the manufacturers warranty and it was, so my customer got this part fixed as part of a warranty procedure. I would suspect that the water spraying over the electronics of the Hot Water Service was probably also causing the fault code II to show up.
It doesn't matter what type of plumbing job you have for our amazing staff at Mayfair Plumbing and Gasfitting we can always help you. We offer plumbers on call 24 hours a day 7 days per week and can have a licensed plumber attend with in the same hour if needed and can also offer same day hot water repairs, so next time your looking for a great plumber at a fair price think MAYFAIR, a trusted name for plumbing solutions for over 20 years in Adelaide and don't forget to visit us at: http://www.yelp.com.au/biz/mayfair-plumbing-and-gasfitting-adelaide-2
A home owners check list before engaging a Torrens Park Plumber:
When it comes to gluing PVC pipe and PVC fittings there are two very important things to remember, always use primer and always ensure your PVC fitting and PVC pipe is clean by starting off with these two things in mind your on the way to getting a water tight connection.
OK so you want to have a go at gluing some PVC pipes together whether it may be for a water line, sewer drain or maybe some storm water pipes, well you are going to need a few things to get started:
If you have cut a piece of PVC pipe it its very crucial that this is now filed free of any burs and dags, it needs to be smooth enough that if you were to run your finger around the pipe it wouldn't cut you and there fore leave no score marks in the glued connections when they are put together which could lead to a leak in the glued connection.
Once it has been established that the PVC pipe and PVC fittings are clean it is then time to apply the PVC primer fluid. In most circumstances these days the manufacturer supply some type of applicator whether it be a brush, foam roller or a dobber, if not I recommend acquiring a brush yourself, it is not recommended to get the priming fluid on your skin so the gloves are very important at this stage of the PVC gluing process. You can get priming fluid in a few different colours such as red and purple and if needed clear for exposed PVC connections they all work the same.
You must apply an even coat of primer to each piece or fitting that is getting glued, so that means the female part of the joint or socket part and also the male part of the fitting, usually going around giving one liberal coating is sufficient, but a little more can never hurt with in reason of course. Once the PVC priming fluid has been applied it is time to have look applying the glue.
Once again it is a similar process to applying the PVC primer fluid and that means that both fittings must receive a generous amount of glue evenly around the fittings or pipe which ever the case. When putting the fittings together after the glue has been applied it is crucial to note that this must happen straight after the glue has been applied as it will begin to cure rapidly, you may notice some resistance when pushing the fittings together and there fore pressure may need to be applied for up to 30 seconds (each scenario is of course different) until the chemical bonding process has taken place and the glued joint has started to go off or cure. A good indicator that you have achieved a good glued connection is that you will see that the fittings have gone all the way into the female connection the full depth of the fitting and in most cases you will have a nice bead of glue at the end of the female connection.
Now depending of the type of application your glued PVC connection is for curing times will vary and it is important to read the manufacturers literature which is usually located on the container of glue.
For more information don't forget to watch our you tube video below for more helpful hints and tips.
Howdy fellow blog fans, you may remember that just a few weeks ago now I posted a blog about a complete home transformation I was under taking at Semaphore in South Australia, well the time has come in just 4 very short weeks we managed to get this house transformed from its original 1970's state to a completely brand new looking modern house again in only 4 weeks and its looks amazing as you might be able to tell from these pictures above.
Probably the stand outs in this project would be the bathroom renovation and kitchen renovation that we performed. The majority of the first fix and final fix items were sourced from Reece Plumbing Supplies and the branch which we used to assist us with was the Blackwood Store, Kevin Jaekel the store manager was extremely helpful throughout this process and his knowledge of all the various products on the market was very helpful to us during the 4 weeks which we performed this renovation for our customer. The customer was extremely happy with the initial proposal that Kevin from Reece Blackwood submitted for me during the quotation stage and then the high end of quality that Reece's in house products showed in the final fixing stage! Thanks Kevin we will be using Reece again on our next bathroom renovation in Semaphore.
You might ask yourself how we get all of this work done in just 4 weeks? Well the answer is unique, we use all of our trades in house, we coordinate everything in house and keep our customers constantly updated on progress and what steps are taking place daily to ensure the finished product is everything our customers is looking for in a renovation transformation. By keeping the lines of communication continually open between us and our customers everyone knows exactly what and when things are happening, the perfect solution to getting the perfect result every time.
In my short you tube video below about my "bathroom and kitchen renovation at SEMAPHORE" you will see some great shots of the before and after photos from the recent home transformation we performed on Semaphore Road, Semaphore and the various stages which this project went through in only 4 weeks, AMAZING!!!
If your thinking of renovating or completely transforming your whole home feel free to send me an email at firstname.lastname@example.org or find us on our contact us page by clicking on this link. I'd love to hear from you and talk to you about your next project and help you get if off the ground.
Providing quality plumbing services for shop fit outs and how we at Mayfair Plumbing and Gasfitting can help, what ever your shop fitting needs.
My week kicked off as they all usually do, flat out busy after a wet weekend in Adelaide, but it wasn't until Tuesday this week that things really took an interesting turn for the good!
I was approached by RM2 a local shop fitting company to supply a quotation for plumbing services on two tenancy shop fit outs. Later Tuesday I attended the site which is located on the corner of Ashwin Parade and South Road Thebarton known as the Brick Works Markets. The two tenancies which I was asked to quote where a bakery and a cafe. The underfloor drainage had already been installed to suit the new tenancy lay outs in a product known as HDPE piping but the hot and cold pipe work had not yet been installed just a 20mm isolation valve for cold water in the ceiling space for each tenancy had been supplied. The quotation was to supply and install new Rehau pipes to each location for the sinks, taps and hot water systems and then to install the various components as supplied by RM2 Shop Fitters. My quotation was successful and that's when my week got really busy.
So I then proceeded to commence on site Friday, first thing was to get inducted on site by the principal contractor BADGE and get our Safe Work Method Statements (SWMS) approved after the formalities of all this were completed it was time to get down to business and things were moving fast as the opening date for the new Brick Works Market site is Thursday the 25th of June 2015 and as you may be able to tell by the images above there is a little bit to be done still.
My first task was to get the over head Rehau pipe work installed from the cold water isolation valve and also the hot water Rehau pipe work distributed around the tenancy in order to feed the various sinks and appliances. This work had to be performed quick smart as the gyprock was being installed very very fast. I managed to get all of my first fixing pipe work installed by Saturday night making way for a busy week next week.
During this busy week my Makita 18v Cordless Drill broke down on me so I will need to purchase a new drill on Sunday in order to allow me to proceed next week. In my week coming up at the Brick Works Market site I will be performing what is known as Second Fix or Chroming Off, its the part of the project where all the taps, sinks, ice makers, fridges and hot water units all get installed. Once this work has been performed its time for the commissioning of all these various items, making sure they all work properly, don't leak water and produce the right temperature from the Rheem 50 litre electric hot water services we are using.
If your in the process of getting a shop fitted out around Adelaide and you need the services of a licensed plumber visit us here at http://www.yellowpages.com.au/sa/hawthorn/mayfair-plumbing-and-gasfitting-adelaides-plumbing-professionals-15073688-listing.html
Have a great week and until next time stay dry and warm, cheers Aaron.
When we perform plumbing and gas work in the suburb of Woodcroft in South Australia we always show up on time, clean up after ourselves and provide top notch plumbing installations, that would be why our customers in Woodcroft keep requesting a Plumber from Mayfair in Adelaide.
Your typical home in Woodcroft is of a brick veneer construction, meaning that the external structure of the house is brick and the internal walls are 10mm gyprock lined. The Hot and Cold water lines are copper tube ranging from 15mm up to 20mm and the natural gas pipe lines are galvinised pipe ranging from 25mm through to 15mm in size.
During my experiences as a plumber Woodcroft I have found that majority of my customers are in there late 30's to early 40's with a young family. The location of Woodcroft makes this an ideal area for couples to raise a family and now with the introduction of Bunnings at Reynella there is now an even easier way to start your home transformation. Bunnings stock everything you could possibly think of to get your bathroom, laundry and kitchen renovated with items such as Estilo Toilet Suites, Vanity Units, Bath tubs, Hot Water Systems, Hand Basins and HUGE range of tap ware.
I wouldn't say that our "HYDRO JET DRAIN CLEANER" gets a huge amount of jetting work in Woodcroft as majority of the homes sewer drain pipes are constructed of PVC/DWV and are not as susceptible to blockages as the older style of drain lines which were installed prior to the establishment of the suburb Woodcroft and that material was Earthenware/Clay.
If do happen see one of our friendly staff members driving along Pimpala Road or even Investigator Drive be sure to give them a wave the chances are they have already helped you with a Plumbing issue in Woodcroft.
Remember we can always be reached on 0429 361 819 24 hours a day in case of a Plumbing Emergency in Woodcroft.
In an industry plagued with a reputation for un reliability and poor customer service I take great pride in providing my customers throughout Adelaide with the complete opposite and it has helped me grow my business substantially. This week in my blog I wanted to share a few tips on what I believe my customers appreciate from me when they choose to engage me for a plumbing or gasfitting project.
A large part of my work is generated through either referrals or repeat business and below in this weeks blog I will outline a few key points which I have found really work in gaining repeat customers:
I believe that the points which I have made have really helped me stand out from other plumbing firms around #Adelaide, check out what our customers say about us here at: https://plus.google.com/+MAYFAIRplumbingAu/posts?hl=en
Have a nice week, Cheers Aaron
I received a phone call Tuesday night from a customer of myn who lives in the CBD of Adelaide, just off of Halifax Street, he lives a large block of apartments which all have roof top mounted Solar Hot Water Services with Electronic Boost, these are all approximately now 10 years old. Even though we were having a slightly warm week in Adelaide with the average temperature of 20 degrees Celsius each day my customer was reporting only luke warm water from his Beasley Solar Hot Water Service. When I heard this it sounded like the element or thermostat was not operating correctly and he was only getting the solar contribution back to his Hot Water Service, so I made a time for me to attend and investigate the problem.
When I arrived to site the next day I found that access to this hot water service was not ideal and this would be the first challenge of many to over come. Because the hot water unit uses electric boost when the outside temperature is not high enough to produce hot water solely through the solar panels the first place for me to check was the fuse box and see whether the circuit breaker for the hot water supply had tripped, upon inspection it showed that the hot water circuit breaker was still in the on position which is very unusual. It most cases when an element blows it trips the circuit breaker immediately, but not in this case? So I went up onto the roof to inspect the Beasley Solar Hot Water System and investigate further, upon removing the plastic cover which protects the 3.6kw element and the robert shaw thermostat I could smell a burnt electrical smell which is usually caused through the element blowing and sure enough you could see at the back of the element that the wiring/casing had all blown out, but why had the circuit breaker not tripped? What was going on? There was no voltage getting to the electric isolator nor was there any current getting to the thermostat, very bizarre indeed!
The first thing that then came to mind was that this hot water system must be on J tariff (a tariff for electricity which is given to customers outside of peak periods at reduced rates at approximately 11pm and 7am each day on separate meter as seen below) but where is the time clock or J tariff meter? The plot thickens.
I asked my customer if he knew whether or not his hot water water service was on J tariff, he did not recall and unfortunately wasn't able to shed any light on the situation. I then went for a look around the apartment complex to see if I could perhaps locate the box which houses all the electricity meters for the complex and identify whether the hot water units are all on J tariff or not and perhaps ascertain what was going on. The box which housed all of the meters was locked and a key would be required for access which the customer had to obtain from the property managers/strata company.
My customer managed to get a copy of the electricity box key and I then made a time to come back out and have another look at the situation. Immediately after gaining access to the meter box I could see that yes the hot water services to the property all had a J tariff feed to them and my customers J tariff circuit breaker was in the off position, but why did it trip the J tariff breaker and not the main breaker for the hot water unit located at the apartment?
Well after I drained down the stainless steel tank on the roof I found that the element was actually ok inside the tank BUT the external part of the element had blown out causing only a slight disturbance to the power and bypassing the main fuse but tripping out the J tariff breaker hence the reason that the main hot water switch to the house was still on yet we had no power to the hot water system, quite a bizarre situation, but that's plumbing for you some times it can be very challenging and that's where my 20 years of experience kicks into gear.
Once all this was established it was time to change over the element, thermostat and turn all the circuit breakers and isolators back on. By the next morning my customer had nice hot water again and all was back to normal, a situation which is certainly going to go into the memory banks for any further hot water repairs Adelaide.
I hope this weeks blog instalment has been of interest to all of my loyal followers and I look forward to bringing you another exciting addition next week, cheers Aaron.
Over the last few weeks I have been working closely with an existing customer of myn to tailor a complete home renovation for her at a rental property she recently purchased in the western suburb of Semaphore in South Australia, right on Semaphore Road across from the beach and the newly renovated Federal Hotel. We have been working closely together to get everything aspect of the project right so that the end result will be mind blowing.
Included in this home renovation and bathroom renovation will be the following: New 8mm floating timber floors throughout the whole unit, painting of the internal walls and doors, complete bathroom renovation, new kitchen, electrical upgrades including new switch board and various light fittings, stainless steel oven and range hood, 4 burner natural gas cook top and all finished off with a full professional clean at the end. Below are a couple images of the progress so far in only a few days this week.
Moving into next week the in wall hot and cold copper plumbing pipes will start getting altered, this will allow for new mixer style tap ware to be installed come the second fix stage of the project. The bath is also getting upgraded to a larger model and this will also need to be installed this week before the tiler attends. The new bath is nearly another 200mm longer and nearly another 250mm deeper this will be a huge improvement as the customer really likes using the bath after a cold winters day. I will be picking the bath up from Reece in Port Adelaide which is only a short drive from Semaphore through Birkenhead and into the Port. Having a plumbing merchant in Port Adelaide makes my life very easy especially if I need a last minute plumbing pipe of fitting.
Once the bath has been installed and the plumbing all altered in the brick walls and in the ground its then time for the tiler to do his work, he will start off with water proofing, this is a crucial part of the process and very important that this is all done correct. While this is all happening the painter will begin his work throughout the entire unit, this fresh vibrant addition will surely give the place a new lease on life.
In the final weeks it will be time for the floating floors to go in and then the cabinet maker will install the brand new kitchen which will have the new stainless steel appliances installed. The customer has opted for an electrolux electric oven and gas cook top, above these appliances will also be a stainless steel range hood. Its going to look simply amazing, I will have to then install the new close couple ceramic toilet pan and cistern, laundry tub and new vanity unit along with the chrome finished mixer taps which set the whole project off nicely.
While we are in the neighborhood of Semaphore and surrounding suburbs such as Exeter, Glanville, Peterhead and Largs Bay we have approached the surrounding residents to let them know we can also have similar work performed for them if they are interested and from these notifications we have already had an inquiry from a customer who would like us to quote on a bathroom renovation west lakes.
I hope you have enjoyed my latest blog this week, if you would like to speak to me about some home improvements or even a bathroom renovation feel free to visit us on the web at http://www.pinterest.com/masterplumer/plumbing-renovations-adelaide/ or even drop me a line on 0429 361 819, I would be only to happy to talk to you and provide you with a free no obligation quotation and discuss the endless options we can provide for you to suit any budget.
A common problem, but an easy fix to "NO HOT WATER" when you have a Bosch Water Wizard, Bosch 10p and Bosch 16p Hot Water Service
The Bosch Water Wizard Hot Water Services are being phased out of existence as majority of these units are 15 years old plus and have since been replaced with a new model. The Bosch P models which the P stands for "pilot light" are also gradually being phased out of the plumbing market in Adelaide as they are no longer considered energy efficient and are being up graded to newer 5 star rated Hot Water System. BUT if you do still own one of these models and it is not leaking water BUT you have no hot water then in most cases there is a relatively easy fix compared to that of installing a new hot water service.
Its not un common for me to get a phone call from one of my customers saying that the hot water is fluctuating and in some cases there is just no hot water at all, they have been out to there Bosch 16p hot water system or Bosch Water Wizard or Bosch 10p and the pilot light is still lit except there is no burner flame when the hot tap is turned on. This is a symptom commonly displayed when the diaphragm inside the water section of the hot water service has split. The diaphragm allows the gas valve to release gas into the burner chamber and start to heat up the water, if this diaphragm is damaged in any way it will not perform its task properly leading to a "NO HOT WATER" scenario, that's when our customers call the the HOT WATER WIZARDS of ADELAIDE.
So how long does a task such as replacing the water section of a Bosch Hot Water Service usually take? Each scenario is different, but in most cases 1 hour is the total time as we carry the "water section repair kits" in our vans to fix these hot water systems on the spot guaranteeing same day hot water repairs Adelaide. As long as the 2 star head screws which release the actual water section are not corroded and in good condition which can be hit and miss especially with a unit that is over 10 years old removing the water section is pretty easy for a licensed master plumber and gas fitter. Its not just the diaphragm which we replace when putting a water section repair kit through a hot water unit, there are numerous o rings, fibre washers and other various parts such as filters which also contribute to making the gas burner fire correctly again allowing a strong roosters tail looking flame to heat your water.
This is the most common fault with the Water Wizard, 13P and 16P Hot Water Systems that we find as the Hot Water Wizards of Adelaide apart from the heat ex changer leaking and if the heat ex changer has started to leak it really is time to start considering a new hot water system installation Adelaide.
If you do have a relatively old Bosch Hot Water Service and are looking for some help please feel free to find us on the internet via GOOGLE at http://www.truelocal.com.au/business/mayfair-plumbing-and-gasfitting/hawthorn
call the "HOT WATER WIZARDS" of Adelaide today on 0429 361 819
Rinnai Hot Water Service Fault Codes, what they mean and how to fix them. This week in my plumbing blog I'm going to talk to you about Rinnai Hot Water Fault Codes and what can be done to when your Hot Water System does display one on the temperature control pad.
Its not very common but occasionally Rinnai Hot Water Services do break down like everything in life and it needs repairing by a licensed plumber in Adelaide and that's why they call the Hot Water Experts - Mayfair Plumbing and Gasfitting.
OK so you have turned on the hot water tap in the shower or kitchen and there is no hot water, you immediately look at the Rinnai Temperature Control Pad and sure enough its displaying an error code, were to go from here? Glad you asked we have the answers.
It doesn't matter what type of Rinnai Gas Instant Hot Water Service you have it could be a Rinnai B16 REU-VR1620WB, Infinity 26 REU-VR2626WG, HD200e REU-VRM2632WC, B24 REU-VR2426WB, Infinity Enviro 26 REU-KM2635WD, HD250e REU-VRM3237WC, INFINITY 26i REU-VR2632FFUG, B20 REU-VR2024WB, or even a RINNAI INFINITY 32 just to name a few of the Rinnai Hot Water Units that can display the error code, below is a list of the common fault codes that can be displayed and how we the Hot Water Wizards can fix them for you:
If you do run into a situation where you are having trouble with your "Rinnai Hot Water Service" please feel free to contact the Hot Water Wizards of Adelaide on 0429 361 819 anytime of day or night even in an Emergency Plumbing situation or if your problem is not so urgent try visiting us on the internet at www.houzz.com.au/pro/mayfairplum/ we love helping you get your hot water back on and in most circumstances we can fix or replace your faulty hot water system the same day so don't hesitate any further and call now on 0429 361 819 we are waiting for your call.
The week started off in Norwood and finished very late Friday night in Norwood, you could say I spent majority of my week working as a Plumber in Norwood. Norwood is a suburb which is located only a few kilometres from Adelaide's CBD and it has some very old majestic properties making it quite the pleasure to work in and around Norwood. The Parade which is the main road leading in and out is probably what Norwood is well known for with many 5 star boutique shops and also some of Adelaide's finest cafes and restaurants to grab a coffee or even a bite to eat and lets not forget the Bath Hotel for a sneaky wine or a pint or two on a Friday night after a huge week of Plumbing.
As I mentioned at the start of my post I kicked off my week as a Plumber in Norwood, over the weekend a customer contacted me saying they had a blocked drain, fortunately the drain was still going down but very slowly so it could wait till Monday and that was my first job. My customer had accidentally flushed a click on toilet deodoriser down the loo and it had lodge itself inside the 100mm drain pipe work. I started off plunging and roding the pan with my closet auger as there were no external Inspection Points, after about 30 long and smelly minutes I still could not get the blockage to move. It was time to pull out the big guns "the HYDRO JETTER" pressure drain cleaner and sure enough after about 15 minutes of jetting the blocked drain away went the blockage and the customer was back in business, once again the Hydro Jetting Drain Cleaning Machine proved to be king when it came to getting a blocked drain cleaned in Adelaide.
Later on in the week I was also very busy throughout Norwood with everyday plumbing tasks such as repairing dripping taps, leaking toilet cisterns and installing a new kitchen sink mixer tap which a customer of myn had purchased from Bunnings at Kent Town.
To finish my week off I was contacted by a Property Management Company which I regularly help out with various maintenance plumbing and gas tasks throughout Adelaide, they were contacted by one of there tenants late Friday night, the tenant had arrived home to find there Hot Water System gushing with water all over the concrete floor outside. After receiving the EMERGENCY PLUMBING call I made it out to the house within the hour which was in Wattle Park a stones through away from Norwood. The Hot Water System was very old approx 15 years and the top of it had corroded away and had started to expel water. I managed to isolate the water to the Hot Water Service and then turn the energy source off to the unit also. This Hot Water Service will now need to be replaced as there is no way of fixing this particular Rheem Hot Water Unit.
Installing a Gas Pipe Line is much more involved than installing a Water Pipe Line. Gas in Adelaide works on a relatively low pressure compared to that of water even though our main gas infrastructure pipes in Adelaide have done and are still continuing to be upgraded. When you consider that the average pressure of someones water lines to there home is approximately 500kpa on average and the average gas pressures to someones home is approximately 1.4kpa there is a huge differential and this is why it is more complex to design and install a new gas line.
When we as "licensed gas fitters" are looking to install a new gas line there are a few things to take into consideration: How many appliances are we going to be connecting onto? How much gas do these appliances consume and the location of the gas pipe work to be installed. Once these items have all been identified and answered the gas line can then be installed.
So firstly the size of the gas line. As you may have noticed around majority of South Australian homes that the water pipe lines are usually 20mm from the water meter to the house and then most of the time 15mm copper tube is then installed to the various fixtures such as WC's, Wash Basins, Showers, Bidets, Kitchen Sinks and Garden Taps to name a few. With Gas though because we just simply do not have enough pressure around the home from the gas meter you may very well notice that the pipe leading into the house from the meter is actually around 25mm to 40mm in diameter, this is due to the fact that we don't have high pressure into the house so we are therefore relying upon flow through larger diameter pipes.
The layout and amount of the appliances on site will depend on how far a large diameter pipe must travel, for example if a customer has a Gas Continuous Flow Hot Water Service installed towards the back of there home then a large diameter pipe must then be installed all the way to this appliance as a Hot Water Service such as this requires a large amount of gas as it is very thirsty for energy and can consume somewhere in the range of 150 mega joules. Keeping this in mind you also must take into account other items along the way to the Hot Water Service which may need connecting up such as a Gas Cook Top (38 mega joules), portable room heaters (18 mega joules) and Gas Ovens (50 mega joules) these all contribute to the overall size of the gas main as the pipe must have enough flow to supply these appliances as well as the Hot Water System at the end of the line. If the pipe line is too small when all the appliances are in operation they will be starved for gas and not operate to there maximum efficiency.
The materials which are most commonly used are either copper tube or galv pipe work. Majority of plumbers use copper tube as they are geared up to use this because it can not only be used for gas but also water so they are always carrying the various tools needed to install this system such as oxygen and acetylene and Viega crimping equipment. When supporting the new gas pipe line distances to the centres for brackets vary from 1.5m for smaller diameter pipes to then 2.5m for larger diameter pipe work.
Once a new gas pipe line has been constructed and bracketed to Australian Standards by our licensed gas plumbers at Mayfair Plumbing and Gasfitting it must be labelled correctly identifying that the pipe work is carry gas and then tested using a water manometer to ensure no leaks have occurred during the installation process. Once this has been done the various appliances must be commissioned and in most circumstances this is done by using a digital gas manometer. The digital gas manometer is a far more sensitive piece of equipment compared to that of the water manometer and is therefore the preferred method of setting final working pressures of gas appliances such as ovens, cook tops and barbecue's which have regulators that can be manually adjusted. Items such as continuous flow hot water systems and portable gas room heaters adjust there working pressures electronically and there fore do not require adjustment but do require checking with a digital manometer to confirm that they are working to the manufacturers specifications.
Performing the task of sizing a new gas main and then installing it can be daunting for many plumbers and they choose not to get involved with this particular part of plumbing, but with over 20 years of experience on various types of gas installations both domestic and commercial we like to think that our gas plumbers are experts at getting the job done in a professional manner for our customers every time and under budget. If you think that you might be in need of a gas fitters knowledge then please fill in our contact us page and we will be in contact with you shortly alternatively you can call us or text us on 0429361819.
It's been quite an interesting week in Adelaide for me as we head into winter, the phone has been ringing steadily with people inquiring about Hot Water Repairs and Installations Adelaide. Being the Hot Water Wizards we are always busy with Bosch Hot Water Services whether it be a new install or a repair on an existing Bosch Hot Water Service through warranty or just a service call, we do it all when it comes to Hot Water in Adelaide.
In this week's post I'm going to talk about the BOSCH 18e Natural Gas External Hot Water Service. I often get phone calls from my customers who have a BOSCH 18e Hot Water System and they tell me that the unit has stopped working or is leaking water, this is due to the fact that these units are all now at least 10 years old and coming to the end of their working lives. In most cases these are now being upgraded to a newer model called the BOSCH 17e, but that is not always the case as I'm going to explain this week.
A customer in Norwood, Adelaide, South Australia recently contacted with me because we are the "Hot Water Wizards of Adelaide" and wanted some advice on repairing his Bosch 18e, the unit was displaying an error code 14 on his temperature control pad inside the home, which indicates a faulty internal wrap around fuse, this device detects over temperature and causes the Hot Water unit to shut down to protect itself from catastrophic failure. This fuse is located at high level inside the Hot Water Service casing and wraps around the copper heat ex changer. It is approx 3mm in diameter and approximately 1m in length and gets wrapped around the heat ex changer 2 times, it is held in place by a series of stainless steel clips and is then plugged into its relevant terminal connections to communicate with the PCB.
When it comes to replacing a part such as this on a Hot Water Service of this age the most cost effective method of resolving this problem is to supply and install a new hot water service. The reasoning behind this is due to the labour which is involved with actually being able to remove the old fuse and then install a new one. In order to get to the fuse nearly every component of the BOSCH 18e needs to be carefully removed and if you have ever looked inside one of these units it's a mine field to say the least. My customer in this instance insisted on ordering the new part and repairing the existing Hot Water Service, so I did. Once the part arrived from BOSCH I made a time to attend my customer's house and start the repairs. The first components to come out of the unit are related to the gas burner and fan and are relatively easy to remove, it wasn't until I started on the sections of the Hot Water unit which relate to water section that trouble started appearing, corrosion had set in and it started making the removal of further components near on impossible, after much persistence I had to pull up stumps and tell the customer the bad news.
Unfortunately after much perseverance and patience the old BOSCH 18e could not be salvaged, my customer was very understanding and agreed that the only way forward was to get a new BOSCH 17e. As I previously mentioned there was a control pad already installed onsite, this is no longer compatible with the new units and therefore also needs replacing if the customer wants to have a control pad in the future, the wiring is compatible just not the control pad. Swapping over the old control pad with the new is probably the easiest part of the project as the fixing holes line up and the wiring is very simple for a licensed plumber/gasfitter Adelaide.
When it comes to installing the pipe work the configuration (when your standing in front of the unit looking at it) as far as hot on far left and gas on far right with cold in the middle is still the same, but the distances off the back mounting wall have slightly differed, so some adjustments will be needed when it comes to pipe work installation. The mounting holes are now also at slightly wider (centres) so new fixing holes will also be required, all pretty standard stuff when we talk about installing a new Hot Water Service Adelaide.
Once all the pipe work and control pad has been installed and tested including working pressures of the gas on the BOSCH 17e its time to enjoy your HOT WATER! With the new control pad installed my customer can now dial up the desired temperature of their shower or kitchen sink to do the dishes AND as a huge bonus the control pad can also be programmed to completely fill a bath to the desired height with warm water, amazing technology!
Finishing off this chilly week in #Adelaide if you do find yourself in need of some kind of Hot Water Repair please remember our licensed gas plumbers from Mayfair Plumbing and Gasfitting and visit us on the web at: http://www.yelp.com.au/biz/mayfair-plumbing-and-gasfitting-adelaide-3 or call Aaron on 0429 361 819 and discuss your next Hot Water project whether it be gas, electric, heat pump, lpg or solar we can help you.
How many times do I go to a customers house or business in Adelaide as a Class A Licensed Gasfitter with over 20 years of experience and find that some weekend warrior or home handy man has been tinkering with the Gas Pipe Lines, Oh My God! This is totally unacceptable and against the law - STOP IT you are putting lives in danger, if you are not licensed to work with gas then stop touching it NOW!!!! Its only a matter of time until someone or something is blown up and lives are taken through these un licensed people performing these tasks.
Some of the more recent examples I have come across are the following:
In closing this week I think my message has been clear, there is a very good reason why us Gas Plumbers are continually up skilling and have also done a lengthy amount of study to work with gas. People are either not understanding what danger they are putting themselves and others in or simply do not care, BUT which ever it is they need to stop cutting corners it will always catch up with you in life and if it is at the expense of another's life there is no worst outcome, so next time you are thinking anything GAS related in Adelaide call Aaron from Mayfair Plumbing and Gasfitting on 0429 361 819 or visit us at http://www.crunchbase.com/organization/mayfair-plumbing-and-gasfitting I hope you have enjoyed my latest BLOG about being safe with GAS its serious stuff and not to be messed with unless your a licensed Gasfitter Adelaide.
Introducing an AMAZING piece of Plumbing technology that's revolutionised the Plumbing Industry in Adelaide
Introducing an amazing piece of new technology to the Plumbing and Gas industry in Adelaide. There are a lot of Plumbing Companies which still use the traditional Oxy and Acetylene gas and torches to solder copper and brass pipes together and in some circumstances we still use this method at Mayfair Plumbing and Gasfitting when soldering a piece of copper tube, but in "Emergency Plumbing Adelaide" the VIEGA tool is king!
BUT in this weeks blog installment I'm going to talk to you about some AMAZING changes to way we as plumbers join copper and brass pipes together, its called "Crimping" or "Pressing" of copper and brass fittings. At Mayfair Plumbing we use a tool made by a manufacturer called VIEGA, there are now multiple other companies on the market today who also manufacture these tools such as Ridgid, Rothenberger and Kempress. The fortunate thing about these different manufacturers being on the market is that all of the copper and brass fittings for these machines are compatible with each other. In my short you tube video below I have filmed what the VIEGA Pressgun 4B looks like in action when it crimps a 15mm or 1/2" diameter water copper elbow and also some of the more common VIEGA and B Press fittings which we use day to day in our plumbing duties around South Australia.
So as you can see from this amazing video filmed right here in #Adelaide technology has really come a long way as far as the installation and repairs of copper and brass fittings especially in a Plumbing Emergency. As I mentioned in the you tube video these plumbing parts come in all different sizes varying from 1/2" all the way up to 4" in diameter and we at Mayfair Plumbing have the equipment and parts to cover you for all the varying sizes you might need installed.
One of the huge bonuses of the Pro Press and Crimping Technology is that a joint can be put together while there is still water in the pipe making this ideal in Plumbing Emergencies Adelaide if a customer hits there water main while doing a spot of gardening we can quickly attend, expose the copper pipe and slide a VIEGA joiner piece in and quickly crimp the fitting with a our Pressgun 4B. A typical task such as this would involve far more work if it were to be welded using an Oxy and Acetylene Torch and also the chance of a leak is much greater mainly due to the fact that the copper pipe in the ground is more than likely going to be dirty and full of water making it hard to solder up.
We believe that by using this AMAZING piece of new plumbing technology not only does it make helping our customers much easier but it is also saving our customers huge amounts of money as the labour time involved for a copper or brass joint to be performed is far less therefore we are on site for a smaller amount of time costing our customers a lot less in labour charges.
If in the future you are looking for a Plumbing firm who can get the job done quickly and professionally especially in a Plumbing Emergency you now have one extra reason to call Mayfair Plumbing and Gasfitting in Adelaide on 0429361819 or visit us via our link here: http://www.aboutus.org/Mayfairplumbing.com.au You know your plumbing and gas pipes are in good hands with a Plumbing Company that's been around for over 20 years "Trust is a must"
"Gas & Plumbing in Adelaide" - WE DO EVERYTHING!!!!!!! YES anything Plumbing related!!! - Call Mayfair Plumbing today on 0429 361 819
How often do I arrive at a customers house to resolve a blocked drain with my hydro jet drain cleaner and the customer looks at my van sign writing and says "Oh right your a Gasfitter as well?" OR "So you can repair my Hot Water Service as well?" There must be a huge amount of Plumbing firms which only do a very limited amount of plumbing tasks around Adelaide and therefore the public think that they need a different Plumbing Company to help with every type of Plumbing or Gas issue. Well that may well be the case with some Plumbing Companies in Adelaide, BUT this week I'm writing my blog about that fact that at Mayfair Plumbing and Gasfitting WE DO ABSOLUTELY EVERYTHING related to Gasfitting and Plumbing, that's right EVERYTHING!!
So to start things off this week I'm going to outline the Plumbing and Gas task's we perform that people commonly think they need multiple firms to complete there projects for them, in order of popularity.
Gasfitting/Gas Plumbing: I cannot recall the amount of times I get asked if I'm a Gasfitter as well as a Plumber. People are continually amazed by the fact that I can do there whole project for them, from disconnecting a gas oven to installing a dish washer or fixing there running toilet. At least once a week I come across this, its not a problem as I inform my customers that I can most definitely help them out with there Gas and Plumbing work, but it makes it very obvious to me that a lot of Plumbers in Adelaide don't offer both of these skill sets leaving Mayfair Plumbing and Gasfitting with a clear advantage in the Plumbing fields in Adelaide.
Hot Water Repairs and Installations: When people come across a problem with there Hot Water Service they ask if they need to get a Hot Water Plumber and the answer is yes, a Hot Water Wizard of Adelaide and that's what your going to be getting when you call Mayfair Plumbing and Gasfitting. Yes we are experienced in all aspects relating to Hot Water it can be Electric Storage Hot Water Services both mains pressure and low pressure storage units inside a roof, Gas Storage Hot Water both low pressure and mains pressure and Gas Instant Hot Water or even Solar Hot Water Services with Electric and Gas Boosters. Our Hot Water Wizards of Adelaide carry all the parts you would ever need to repair a faulty Hot Water Service in Adelaide on the spot, items such as: Thermo-Couples, Hydro Ignition Packs, Thermostats, Elements, Heat Exchangers, Hydro Generators, Control Pads and Furnaces. So if its Hot Water related we do it ALL!
Backflow Valve Testing, Repairs and Installations:
Protecting your drinking water is a service we offer also offer as Plumbers Adelaide. At Mayfair Plumbing and Gasfitting we use finely calibrated test equipment with needle valves which get laboratory certified every 12 months to ensure we protect your drinking water from contamination. In our short video below it gives you an insight as to what an actual Backflow Prevention Valve looks like and just what some of the components which make up a Backflow Valve Assembly perform to help protect our drinking water in Adelaide, South Australia. Backflow Valves come in various shapes and sizes ranging from 15mm (1/2") all the way to up 150mm (6") in size and the hazard ratings also vary going from Medium Hazard through to High Hazard. In this you tube video you will see a RPZD which is classed as a High Hazard Device and is used to protect potable water from dangerous chemicals and substances such as: Acids, Blood and Fertilisers. These High Hazard rated RPZ Backflow Valve's are used in circumstances where the substances if mixed with drinking water is deemed life threatening, hence High Hazard.
Next time you think about calling a Plumber Adelaide think Mayfair Plumbing and Gasfitting our plumbers are fully trained in every aspect of Plumbing and Gas and can handle any type of Plumbing project you need performed, please call us on 0429 361 819 or contact us via http://www.linkedin.com/pub/master-plumber/88/892/7b3
Is it time to give your Bathroom or Kitchen a face lift? What are you waiting for? Its simple just have a look at this
Performing any type of renovation can be quite the daunting experience regardless of the scale that is involved, it can be just a minor face lift or as seen in the picture above a full scale bathroom renovation where the whole internal of the bathroom is demolished and everything is removed for new plumbing pipes to be installed.
In the picture above you can see that the walls of the bathroom are brick, this home was built back in the early 1900's like most of the homes throughout Prospect, majority of the homes were constructed from solid brick which is a lot different to today's methods of construction where timber framing with a gyprock internal lining is much more common.
Installing new copper hot and cold pipes into a solid brick bathroom can be a challenge and very labour intensive. To enable me to get this job done professionally and quickly with minimal mess I have invested in a dustless wall chasing machine as shown in the images below. Purchasing a piece of kit like this puts a decent dent in your back pocket, BUT the results speak for themselves, its truly amazing. The Ramset wall chaser has a variety of options to choose from such as variable depth and width adjustments and the vacuum which can be used for either wet or dry applications and periodically the filters vibrate themself clean. Using this piece of machinery sure does help with the overall process involved with installing new copper hot and cold pipes into a bathroom renovation.
Once the chasing has been performed with the Ramset wall chaser its very easy to remove the pieces of brick wall where the new pipes will be installed, they just about fall out, leaving minimal jack hammering work to be performed, which in turn minimises the structural damage to the house by having less vibration impact to the structure which is a huge bonus as most of these properties are in a delicate state and the less impact through jack hammering its structure the better.
Once the wall chases are performed and ready for installation of the new hot and cold copper pipes the procedure is fairly straight forward using Viega Pro Press Technology, this involves using copper fittings (see image below) which actually get crimped together using the Viega Pro Press Gun (see image below). These fittings are slightly more expensive BUT the installation procedure is so simple and nearly 100% guaranteed leak free, gone are the days of using the oxy and acetylene welding torch and the risk of water leaks and naked flames with potential for fires and hot work permits.
Later in the week I was contacted by a past customer who I had tested a backflow valve for at Marion SA 5043, on Marion Road a few months ago he is now renovating an apartment down at Glenelg (The BAY), just off of Brighton Road near the SANFL Glenelg Tigers home ground oval. The old kitchen in place was the original design supplied when the apartment was first built probably back in 1970. The hot and cold taps like many of these apartments from this era had the taps located above the sink with a spout in the middle over the sink.
These days when most people do a kitchen renovation they opt to have the hot and cold points for the new taps lowered below the sink height and have a nice new mixer style tap installed (as seen below), this is where my Ramset Wall Chaser comes into action again, lowering these copper pipes for this alteration is made very simple and clean when using the right equipment which always makes my customers happy.
In most cases the the 50mm PVC/Galv waste pipe for the kitchen sink also needs adjustment in the way of lowering it by approximately 300mm to accommodate the new double sink and the correct plumbing which goes with this during the second fix process such as a double bowl connector and combination s and p trap to apply with South Australian Plumbing Codes AS3500.
So as you can see by this weeks blog Mayfair Plumbing and Gasfitting are completely set-up to cater for all your Bathroom and Kitchen Renovations in Adelaide, call us today on 0429 361 819 or contact us via: http://www.pinterest.com/masterplumer/plumbing-renovations-adelaide/
Has your plumbing sprung a leak in Springfield, SA 5062? Well you are going to need a local plumbing firm who operates out of the Mitcham city council district and that answer is MAYFAIR Plumbing and Gasfitting, yes MAYFAIR, call NOW!!!
Being based in Hawthorn, South Australia 5062 allows us to access the suburb of Springfield with plumbers quickly to help with all types of Plumbing and Gas issues that our customers come up against, it doesn't just have to be an emergency plumbing leak they may have found, it can be Hot Water Repairs and Installations, Bathroom Renovations, Installing Water Purification Taps, Pre-Purchase Property Inspections, Camera Inspections or perhaps even servicing there Gas Room Heaters before the chill of winter arrives in Adelaide.
Springfield is home to some of Adelaide's most luxurious houses and you are sure to find lots of plumbing and gas pipes located on these properties. Knowing where to find a Water Shut-off Valve or how to isolate the Natural Gas takes experience, the experience you can only gain by working as a Plumber Springfield in the city council of Mitcham day and night 24/7, a task which Mayfair Plumbing and Gasfitting often do.
In our short video below you will see all the different areas around Springfield which we have worked on over our 20 years of being Professional Plumbers Springfield, South Australia 5062.
Carrick Hill would have to be one of Springfield's most historic residences located at 46 Carrick Hill Drive, Springfield, SA 5062. Its an ideal location to take the children on a Sunday afternoon and explore the Story Book Trail and learn about nature. Carrick Hill also provides a perfect back drop for weddings and functions, its beautiful luscious gardens are simply majestic and if you've never been to Carrick Hill put it on your list of things to do.
Mayfair Plumbing and Gasfitting know that working as Plumbers Springfield many of the houses will have a commercial style arrangement for there plumbing, with items such as sewer and storm water pumping stations, hot water flow and return systems with circulation pumps in line, rain water harvesting plants and multiple bathrooms so having experience in Domestic, Commercial and Industrial Gas and Plumbing is very advantageous working as a Plumber Springfield, SA 5062 in Adelaide.
If you live on Delamere Ave (both in Netherby and Springfield), Springfield Ave, Glenwood Road or on Elmglade Road just to name a few of the beautiful streets in Springfield we are here to help you, let your Plumbing problems become our Plumbing Emergency contact us at http://adelaide.cylex.com.au/company/mayfair-plumbing-and-gasfitting-23551855.html.
Are your storm water drains ready for winter? Its just around the corner, don't get caught out with blocked drains.
Its been long time between drinks in Adelaide when we talk about the last time a good amount of rain fell from the sky and its so easy to neglect our storm water drains underground, we all have so much more important day to day things happening in our lives to be thinking about storm water drains UNTIL it rains heavily and that's not far away.
I have already been busy over the past couple of weeks assisting my customers with there blocked storm water lines in preparation for the harsh winter rains which we are soon expecting in Adelaide. The most recent blocked storm water line which I attended to with my state of the art Hydro Jetting Machine was out in Adelaide's Northern Suburbs in the council district of Tea Tree Gully. My customer had recently built a beautiful nice new home and had the rear court yard concreted and I believe that the slurry etc from this may have found its way down the storm water drain pipes, over the summer months we haven't had much rain to speak of and this slurry material has set like a rock inside of the storm water drain lines, with this comes blocked storm water drains, see images bellow!!
Many of the domestic type storm water drain pipes in Adelaide need the occasional bit of maintenance from a Hydro Jet Drain Cleaner to keep the flow going in there storm water lines, this is because most houses either sit level with the street water table or only just above it. This being the case it means the storm water lines are continually holding water and this allows silt to settle in the drain slowing down the flow of water during a storm. But with yearly flushing from a Hydro Jet Drain Cleaning Machine it can help to avoid the need for a Plumbing Emergency if your drains over flow.
In this weeks blog I have also attached one of my you tube videos. In the video below you will get to see what the hydro jet drain cleaning machine actually looks like, you will also get the opportunity to look at the different types of pipes and fittings that are used when installing drains in South Australia and finally it will give you a better understanding of why only a Hydro Jetter will get your drains cleared fast and why the conventional electric eel cannot.
After viewing my short 5 minute you tube video you can now understand a little bit more about plumbing and how our plumbers at Mayfair Plumbing and Gasfitting handle blocked storm water lines. Because of the unique compact set up which we operate our Hydro Jetter in this enables our blocked drain plumbers to get into various tight locations others may not be able to. We clear blocked storm water lines any where around Adelaide, from Para Hills to Magill, from Springfield to Burnside, from Semaphore to Glenelg and from Woodville to Port Adelaide just to name a few locations, being based only 5 minutes from the CBD of Adelaide in Hawthorn gives us huge flexibility to be able to go anywhere to help our customers with there blocked storm water drains and at anytime of day or night 24/7 we can unblock drains.
If you have any questions please feel free to click on the following link http://www.aubiz.org/details/may-fair-plumbing-and-gas-fitting OR call 042361819 and ask for Aaron the owner operator at Mayfair Plumbing and Gasfitting.
CALL NOW: 0429 361 819
Aaron Stewart owns and works in the business of Mayfair Plumbing & Gas Fitting from there offices now based in Adelaide, South Australia. Aaron and his team of licensed plumbers and design consultants are passionate about there work. In this blog they will bring you plumbing and gas tips gathered from around the globe over 20 plus years of experiences in the many different fields of plumbing. If you are looking for a plumbing firm who can do everything from design, construct, project management and scheduled on site maintenance contact the Mayfair Plumbing Group.